Gastroback 41402 Operations Instructions download pdf (Page 6)

Clear a blocking

If the worm housing is blocked no mince comes out of the mincer while operating or the motor stops

moving automatically because of the overload protection.

ATTENTION: If a blocking occurs turn OFF the appliance immediately. Clear the problem

before turning on the motor again.

1. Turn the appliance OFF and then take the feedstick out of the feed funnel.

2. If the motor stopped running because the overload protection turned itself on you have to

turn the appliance OFF to undo the overload protection.

3. Turn the motor ON and OFF by turns to loosen the blocking.

ATTENTION: If the motor still does not start running turn the appliance OFF, pull the plug

and clean the appliance.

Waste disposal

The appliance has to be deposed by the definition of the regional waste disposal of

electrical scrap.

If necessary get information of the regional waste management enterprise.

Warranty

We guarantee that all our products are free of defects at the time of purchase. Any demonstrable

manufacturing or material defects will be to the exclusion of any further claim and within 2

years after purchasing the appliance free of charge repaired or substituted.

There is no Warranty claim of the purchaser if the damage or defect of the appliance is

caused by inappropriate treatment, over loading or installation mistakes.

The Warranty claim expires if there is any technical interference of a third party without

an written agreement.

The purchaser has to present the sales slip in assertion-of-claims and has to bear all charges

of costs and risk of the transport.

The warranty becomes invalid and GASTROBACK does not assume liability if:

1. The user did not follow the instructions or the user did not use the appliance as stated and

only for thus use (improper use, misusage).

2. The appliance was connected to a power supply with improper current.

3. The mincer got opened by an unauthorised person.

4. Other then original spare-parts got used.

5. The appliance was in commercial use. Used up parts from commercial use are no

warranty claim.

The mincer is intended for use in the household only!

Possible problem Easy solution

Always assemble the appliance for storing. This way the parts are protected and can not get lost.

ATTENTION: Never pull, rip, bend, clamp, squish or knot the line cord.

Trouble shooting guide

The mince is not fine enough.

There are still ingredients in the feed funnel

but no mince is coming out of the mincer.

The motor stops running while operating.

After cleaning the motor does not get started

again when turning the appliance ON.

The mincer blocks up permanently

while operating.

The worm housing moves or loosened while

operating.

The mince leaks out at the side of the

closing ring.

Use a smaller mince plate and/or mince the ingredients more then

once.

The mincer is blocked. Turn the appliance OFF immediately and operate

according to the instructions ´Clear a blocking`.

The overload protection might got activated. Turn the appliance OFF

immediately and operate according to the instructions ´Clear a blocking`.

• Is the power cord plugged in?

• The motor might be blocked with some hard substance (for example a

bone). Turn the appliance OFF immediately and pull the plug.

• Disassemble and clean the appliance. Operate according to the

instructions ´Care and cleaning`.

• If the problem is not solved after the cleaning, take the appliance

for technical maintenance and repair to an authorised specialised

reparation shop.

• To ensure that the mincer does not seize, never operate it under

excessive pressure. Operate in a slow and constant pace. Do not

try to rush the procedure by pushing down the meat with force.

• For mincing hard ingredients really fine start with the grinding disc

with the bigger holes. Mincing the second time use the finer mincer

plate.

The screw plug loosened. Turn the appliance OFF immediately. Press the

worm housing with one hand against the motorblock using the other

hand to tighten the screw plug turning it clockwise.

The closing ring is not screwed on tight enough. Turn the appliance OFF

immediately and then pull the plug. Tighten the closing ring but do not

overwind the winding. If the problem still occurs disassemble and clean

the appliance.

2928

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Gastroback 41402 Operations Instructions Page 6

Comments to this Manuals

Related products and manuals for Mincers Gastroback 41402